Humidity factor is a potential to damage the building structure, particularly in some parts of the building made of wood. For this example we will discuss how to repair damage to the wooden door which is caused by humidity, the following are the steps :
Scrape and sand.
Scrape with a spatula damaged areas to remove all the paint bowls and half lifted. This step is very important because if done right, once painted the door would finally get up the paint in those areas. Then sand the whole door with a soft sandpaper.
Clean the door.
Clean the door with a damp cloth to remove all traces of paint and dust that have caused the scraping.
Apply the paste.
There is a white pasta because the door is white (for example). If you prefer there are also pasta cherry, oak, mahogany, etc., Imitating wood. It is important to consider the finish that will give the bell to choose the pastaWe apply the paste with a spatula chosen on the damaged areas, reproducing the design of the door where necessary. The spatula is especially useful for smooth surfaces and corners. In cases where the door has rounded reliefs, relief play shaping the dough with your hands.
IMPORTANT: In areas where we need to fill deep holes is preferable not to cover the hole once, but it gradually in layers. In this way, we would apply a layer, we would dry out and we would apply layers and allowed to dry to fill the entire gap.
Let dry and sand.
Let it dry pasta that we applied. The time required can vary depending on the pasta that we have chosen, in any case, is indicated on package directions. Our pasta, for example, requires a drying time of 24 hours. Once the paste dries, re-sand the areas where we have applied. This is to remove excess paste and tweak to smooth areas so that the pasta is perfectly integrated into the door.
Painting or varnishing.
In our case, we will paint the door white as mentioned at the beginning. To this end, we recommend water glaze. Traditional glazes were diluted in a special solvent or thinner are more difficult to implement and give off a strong smell and slightly toxic. By contrast, the new glazes the water are easier to apply, easy to clean if you spotted something and not give off that smell so bad.
When painting white on white, nothing is more wash the face at the door and they are well covered the damaged areas, so that two coats is usually sufficient. In any case, it is important to hand dry thoroughly before applying the next (about 24).
In the event that our door is wood color and we used a paste wood color, choose a desired color paint and follow the instructions on the package as a solvent and drying time, simple and easy......
Scrape and sand.
Scrape with a spatula damaged areas to remove all the paint bowls and half lifted. This step is very important because if done right, once painted the door would finally get up the paint in those areas. Then sand the whole door with a soft sandpaper.
Clean the door.
Clean the door with a damp cloth to remove all traces of paint and dust that have caused the scraping.
Apply the paste.
There is a white pasta because the door is white (for example). If you prefer there are also pasta cherry, oak, mahogany, etc., Imitating wood. It is important to consider the finish that will give the bell to choose the pastaWe apply the paste with a spatula chosen on the damaged areas, reproducing the design of the door where necessary. The spatula is especially useful for smooth surfaces and corners. In cases where the door has rounded reliefs, relief play shaping the dough with your hands.
IMPORTANT: In areas where we need to fill deep holes is preferable not to cover the hole once, but it gradually in layers. In this way, we would apply a layer, we would dry out and we would apply layers and allowed to dry to fill the entire gap.
Let dry and sand.
Let it dry pasta that we applied. The time required can vary depending on the pasta that we have chosen, in any case, is indicated on package directions. Our pasta, for example, requires a drying time of 24 hours. Once the paste dries, re-sand the areas where we have applied. This is to remove excess paste and tweak to smooth areas so that the pasta is perfectly integrated into the door.
Painting or varnishing.
In our case, we will paint the door white as mentioned at the beginning. To this end, we recommend water glaze. Traditional glazes were diluted in a special solvent or thinner are more difficult to implement and give off a strong smell and slightly toxic. By contrast, the new glazes the water are easier to apply, easy to clean if you spotted something and not give off that smell so bad.
When painting white on white, nothing is more wash the face at the door and they are well covered the damaged areas, so that two coats is usually sufficient. In any case, it is important to hand dry thoroughly before applying the next (about 24).
In the event that our door is wood color and we used a paste wood color, choose a desired color paint and follow the instructions on the package as a solvent and drying time, simple and easy......
Tidak ada komentar:
Posting Komentar